Close
Filters
Apply Filters

NARROW DOWN


BRAND
-

Genasys - LRAD 500X MMT Helicopter-Mounted System
$0.00
The LRAD-500X MMT is an advanced air-to-ground communication system that is self-powered and completely autonomous from other aircraft systems. The LRAD 500X MMT broadcasts loud, highly intelligible voice messages and attention commanding warning tones out to 2,000 meters over wind, engine and rotor wash. Classified as a payload by the FAA, the LRAD 500X MMT easily mounts to the cabin floor of a wide range of helicopters using cargo tie-down quick disconnect fittings. Featuring a rugged mount with a full range of pan & tilt motion and an integrated rechargeable power pack that provides 4 to 6+ hours of continuous operation, the LRAD 500X MMT significantly enhances the operational effectiveness of airborne law enforcement in a variety of missions.
  • Ruggedized mount allows operator to aim and lock LRAD into position
  • Self powered for 4 to 6+ hours of continuous operation when fully charged
  • Integrated battery monitor displays battery charge level reading
  • Simple to install and operate
  • Control unit may be mounted on the back of the LRAD or operated via remote cable (included)
  • Mounts to helicopter cabin floor with included jaw clamps
  • Powerful, intelligible communication to 2,000 meters
  • Variable beam width for extended coverage
  • Quickly installed and removed from helicopter
  • Self-powered
  • STC not required
Add To Cart
X
Quantity:
DFND - Hybrid LS Compression Shirt
$0.00
PATENTED DESIGN. The Hybrid long sleeve compression shirt is a Unisex Patented Design that features a combination of moisture wicking breathable 70 denier and powerful embedded inserts made of 105 denier that enables the body to maintain a more balanced posture, enhance power out and decrease the possibility of injuries. The sleeves are constructed with graduated compression to help enhance blood flow and is part of our sleepwear recovery program when worn with the Recovery Compression Tight. Each garment is constructed with flatlock seams to help reduce chafing.

FEATURES:
  • Made in the USA - Berry Compliant
  • Anti-Bacterial
  • SPF50+ Sun Protection
  • Moisture wicking to help keep you dry
  • 360 degree stretch
  • Circular knit fabric for maximum muscle containment
  • 105D 65% Nylon / 35% Invista Lycra
  • 70D fabric 70% Nylon / 30% Invista Lyrca
  • Offered in sizes: S, M, L, XL, XXL, & XXXL
Add To Cart
X
Quantity:
DFND - Women's Recovery Compression Tight
$0.00
The DFND Recovery Tight is powerful gradient compression featuring 105 deniers circular knit fabric that will increase your blood flow and give you maximum muscle containment to help reduce soreness and swelling. It is the ultimate tight to wear post-training and sleeping for faster recovery. Each garment is constructed with flatlock seams to help reduce chafing and includes a comfortable waistband for extended wear. It is not recommended for training. Should be used for 3-5 hours after training and icing.

FEATURES:
  • Made in the USA & Berry Compliant
  • Faster recovery
  • Reduced soreness
  • Reduced swelling
  • Graduated construction enhances blood flow
  • Reduces chafing, edema and cellulitis
  • Full Length
  • FUZE Antibacterial
  • SPF 50+ Sun protection
  • Moisture-wicking lightweight & breathable
  • 360-degree stretch
  • Powerful 105D circular knit fabric
  • 65% Nylon / 35% Invista Lycra
  • Offered in sizes: XS, S, M, L, & XL
Add To Cart
X
Quantity:
DFND - Malibu 5" PT Short
$0.00
The Malibu 5" short is the ultimate lightweight run short with a zipper side pocket and ultra-soft built-in briefs for the support to sustain many miles. The zipper pocket is ideal for keys, ID cards or other small essentials.

FEATURES:
  • USA & Berry Compliant
  • 2 way stretch anti-microbial fabric for ultimate comfort
  • Ultra-soft mesh liner
  • Zipper pocket
  • 5" inseam
  • 100% polyester fabric
  • Unisex sizes: XS, S, M, L, XL, & XXL
Add To Cart
X
Quantity:
Galvion - Individual Power Manager
$0.00

Often operating for prolonged periods in remote and austere environments, The Army needs flexible and dependable power solutions. Specifically designed to address their demanding requirements, The Army Core Kit combines a Squad Power Manager SPM kit containing standard scavenging cables, batteries, and load cables. Includes SPM BB-2590, BA-5590 Discharge, Dual PRC-148/152, 4 Port USB-A Charger. With this kit, you can scavenge power from any available source and automatically convert that power to reliably charge and run vital equipment. The Army Core Kit includes connectors for civilian and military batteries, vehicle power outlets, solar blankets, military radios, satellite communication systems, smartphones, tablets, laptop computers, and more.

FEATURES:
  • FIELD PROVEN - In use with all USSOCOM units, U.S. Army SFABs, and multiple international SOF units
  • USAF CERTIFIED SAFE-TO-FLY - Can be used while in-flight and/or connected to aircraft power. When used with the SPM, the Nerv Centr SoloPack and SharePack can be recharged while onboard
  • PLUG-AND-PLAY - Intelligent power management software and smart cable technology makes switching between power sources and connected devices intuitive and seamless
  • SIX UNIVERSAL PORTS - Delivers mission-critical capability, powering devices, managing energy sources, and charging up to five batteries -simultaneously, without any manual reconfiguration or reprogramming
  • CUSTOMIZABLE - The Squad Power Manager Special Forces Kit can be upgraded with additional cables to support UAS and UGV systems, field medical equipment, EOD equipment, power tools, sensing/imaging/targeting systems, and more
  • RUGGED - Fully ruggedized for military use, the Squad Power Manager withstands temperatures ranging from 30°C to 70°C, and can even operate when fully submerged in more than a meter of water
DIMENSIONS: 2.5'L x 3.7'W x 0.68'H CERTIFICATIONS:
  • MIL-STD-810G
  • MIL-STD-461F
Add To Cart
X
Quantity:
Galvion - Charger/Enhanced Charger
$0.00

A lightweight, rugged, battlefield-ready solution to charge the Solopack and Sharepack batteries in under three hours. The Nerv Centr chargers harvest power from various energy sources, including vehicle, solar, AC power and other common sources.

FEATURES:
  • Charges SoloPack or SharePack within 3 hours
  • Displays charging and error status
  • Operates across: -20°C to +40°C (-4°F to +104°F)
  • The charger weighs 425 g (15 oz)
  • Fits in an M4 magazine pouch
  • Works across worldwide AC voltages
  • Ensures lithium battery safety
  • Design features Velcro strap for cable management
  • Includes Nett Warrior cable to attach to the battery
ADDITIONAL FEATURES:
  • Enhanced Charger weighs 445 g (15.7 oz)
  • Field charger that harvests power from various energy sources, including vehicle, solar and other common power sources
  • Has a USB port to charge IOS and Android devices
  • Immersion proof to a depth of one meter (3.28 ft) as per MIL-STD-810 Method 512.6
  • The rugged design prevents damage from moisture, sand, and typical soldier wear-and-tear
  • Includes four ports: Nett Warrior input port, AC input port, Nett Warrior charge port, USB charge port
DIMENSIONS: 6.5'L x  3'W x 1.5'H CERTIFICATIONS:
  • MIL-STD-810 Method 512.6
Add To Cart
X
Quantity:
LRAD - Green Laser Dazzler (Shown with LRAD-RX)
$0.00
Add To Cart
X
Quantity:
HDT Global - Command and Control Solutions
$0.00
HDT Command and Control solutions provide flexibility, durability and reliability for those who need to establish operations in the field and adapt to changing mission requirements. Comprised of lightweight components designed with mobility, human capital and logistics in mind, our display systems, command tables, video distribution solutions, audio systems, tactical furniture, lighting, flooring and cable management solutions allow users to focus on the mission, not on the infrastructure.

Add To Cart
X
Quantity:
Artemis Bio-Solutions - MST Micro Sprayer-Fogger
$0.00
Artemis Bio Solutions MST-Micro ULV Cold Fogger is the only fogger available designed specifically for the proper deployment of all Artemis Bio-Oxygen, Bio-40, Bug Interceptor, and disinfecting products. BENEFITS Corrosion and Chemical Resistant: The MST-Micro is constructed entirely of corrosion and chemical resistant materials including stainless steel, nickel plate, chrome, and viton nuba. Delivers the Perfect Fog: The MST-Micro is engineered to deliver the perfect micron droplet at the perfect flow rate, maximizing efficacy, while avoiding over saturation. Convenient, Affordable and Effective: Properly atomizing Artemis products with the MST-Micro cold ULV fogger will save you time and expense on your next job. Easy to use, inexpensive, and engineered to deliver the perfect amount of fog to treat any area. With over 30 feet of fog throw you can treat thousands of square feet in seconds.

FEATURES:
  • Atomizes the perfect droplet size/Delivers recommended flow rate
  • Over 30 feet of fog throw
  • 1.5 gallon reservoir
  • Available in 110v and 220v
  • Lightweight
  • Treats thousands of square feet in seconds
  • Padded shoulder strap
Add To Cart
X
Quantity:
Artemis Bio-Solutions - Bio-Oxygen® Chem-Decon
$0.00

Our powerful Bio-Oxygen® Chem-Decon product is proven to effectively cut through bio-film for safe removal and neutralization of tear gas, smoke damage, explosive residue, chemicals used in manufacturing of methamphetamine and all types of biological and chemical hazards.

Bio-Oxygen® Chem-Decon proves its value with excellent results from clearance tests, significantly lowered remediation costs, reduced the overall manpower hours, reduced equipment needs, and other supplies otherwise necessary to meet health and safety guidelines. Bio-Oxygen® Chem-Decon is inherently biodegradable, non-toxic, environmentally safe, reliable and cost effective.

SPECIFIC USES:
  • Meth Lab Remediation
  • Smoke Damage
  • HAZMAT
  • Crime Scene Clean-Up
  • Hoarder Clean-Up
  • Trash Outs
  • Petroleum Storage Tank Clean-Up, etc.
Add To Cart
X
Quantity:
Artemis Bio-Solutions -  Defender 2 Minute Disinfecting Wipes
$0.00

Artemis Defender 2 Minute Disinfecting Wipes are EPA registered and tailored for cleaning and disinfecting of virtually any hard surface. Pre-moistened with a bleach-free, alcohol-free and non-staining formula, these disinfectant wipes are effective against MRSA, VRE, HIV-1 and a wide range of other forms of pathogenic bacteria.

Use Artemis Defender 2 Minute Disinfecting Wipes to clean and disinfect non-porous personal protective safety equipment, protective headgear, hard hats, half mask respirators, full face breathing apparatus, gas masks, goggles, spectacles, face shields, silicone rubber or PVC hearing protectors and vinyl covered ear muffs. Rinse all equipment that comes in prolonged contact with skin before reuse with clean warm water and allow to air dry.

FEATURES & BENEFITS:
  • USA EPA GOLD SEAL registered product
  • Solvent, Alcohol, Bleach free, sanitizing and disinfecting wipes
  • Kills Antibiotic Resistant Bacteria
  • Fast, Effective kills bacteria in just 15 Seconds
  • Cleans, Disinfects & Deodorizes in one step
  • Made with scrubbing fibers yet won't scratch surfaces
Add To Cart
X
Quantity:
Artemis Bio-Solutions -  Dont Tread on Me Field Wipes
$0.00
Whenever water is not available, use Don't Tread On Me Field Wipes.

Extra Thick Heavy-Duty Towels Are Ideal for:
  • Military personnel
  • Emergency
  • Response Teams
  • Law Enforcement Officers
  • Campers/Motor homes
  • Hunting/Camping/Fishing
  • Rock Climbers/Cyclists
  • All Outdoor Activities
  • Muddy Dog Paws
FEATURES & BENEFITS:
  • Unscented
  • Alcohol-Free
  • Waterless-no need to rinse
  • Removes Germs, Dirt and Odor
  • No Mess
  • Prevents cross-contamination
  • Convenient Flat Pack
  • Conditions and moisturizes skin
  • Extra thick Heavy-duty towel will remove dirt and grime.
  • Eliminate odor and leave you clean and fresh
Add To Cart
X
Quantity:
BeaverFit - Air Delivery Platform
$0.00

The BeaverFit Air Delivery Platform is designed to simulate exiting an aircraft in an operational environment. The Platform itself can be customized to meet different training requirements and can be installed on top of a variety of container towers.

FEATURES:
  • Roof Platform
    • Fast rope entry
    • Rooftop anchor points
  • Lower Platform
    • Trap door hatch
    • Associated anchor points and fittings
  • Chinook Exit (optional)
    • Helicopter rappel or fast rope exit
    • Associated anchor point and fittings
  • Rappel Rail
    • Internal safety line
    • Multiple anchor points
  • Helicopter Skid
    • Skid simulation
    • Non-Slip entry/exit

Add To Cart
X
Quantity:
BeaverFit - Obstacle Courses
$0.00
BeaverFit Obstacle Courses are designed to assess, develop and refine warfighter survivability, strength, endurance and responsiveness. With a library of over 20 obstacles, our courses actively engage mind and body - improving cognitive skills, refining coordination and increasing the overall efficiency of the warfighter before they ever step foot on the battlefield.



Add To Cart
X
Quantity:
BeaverFit - Custom Rig / Rack / Facility
$0.00
BeaverFit Modular Rigs and racks are specifically designed to enable strength coaches or other fitness leaders to create training spaces catered to their unique requirements. Building on the foundation of baseline four-foot lifting stations and six-foot bays, these modular rigs and racks can be configured to include rope climb stations, ascending or descending monkey bars and a variety of securable and open storage and shelving options.

Add To Cart
X
Quantity:
BeaverFit - Training Towers and Complexes
$0.00
BeaverFit Special Operations Equipment is purpose-built to meet each client's unique mission essential tasks and training requirements. Our collaborative requirements-based design and build process enable training towers & complexes ranging from relatively simple, small footprint single modality training solutions to large, multi-modality, design intensive facilities and training complexes.

Add To Cart
X
Quantity:
JBC Corp - PIG Pack Ð Platform Interchangeable Gear
$0.00

The 'Platform Interchangeable Gear' pack is a unique multi-purpose, multi-use, mobility pack that allows the user to configure the pack to suit the mission and personal preference. The PIG is comprised of two separate packs which mount on a base that is carried utilizing either a single strap that slings across the chest or with 2 straps for conventional backpack style. A smaller medical pack containing critical trauma supplies attaches in the front for immediate access. The PIG Pack is equipped with the JBC's exclusive Pack Lighting System. The lighting system is NVG friendly and does not interfere with your night vision. The pack is user friendly, with all contents visible, or labeled for easy identification.

Add To Cart
X
Quantity:
Cardiac Science - Powerheart AED G3 Semi-Automatic Package
$0.00
  • Powerheart AED G3 PLUS SEMI-Automatic package with voice & text display; biphasic waveform, and internal memory.
  • Includes: AED(Automatic External Defibrillator), Battery, Carry Case, Ready Kit and Extra set of Adult electrodes
  • Features: Rescue Coach Instructive prompts and metronome for proper CPR compression frequency & Manual shock button
Add To Cart
X
Quantity:
Cardiac Science - Powerheart® G5 Semi Auto Quick Response Package - ICPR Feedback
$0.00

Package Includes:

  • (1) G5 Semi Auto single language US English AED
  • (1) G5 IntelliSense Battery
  • (1) set G5 Intellisense adult defibrillation pads
  • (1) set of ICPR Feedback pads
  • (1) Semi-Rigid Carry Case
  • (1) Universal Ready Kit
  • (1) AED Manager
  • (1) USB Cable
  • (1 set) printed G5 User Guide, Steps to Rescue, Getting Started (ENG)
  • (1 set) printed G5 User Guide, Steps to Rescue, Getting Started (ESP)
  • (1) set printed multi-language User Guide
Add To Cart
X
Quantity:
Strategic Operations - 6-N-1 TCCC Trainer
$0.00
The 6-in-1 trainer is a one of a kind training aide which enables medical personnel to apply medical techniques without the risk of injury to a live patient.Ê With the 6-in-1 trainer, medical personnel will be able to place NPA's, OPA's, perform surgical airways, needle thoracentisis, and sternal/proximal humeral intraosseous catheter insertion.Ê The Hyper-Realistic™ head and upper torso are constructed from a foam-filled, anatomically similar resin skeleton with user-repairable silicone body skin, neck skins, tracheas, and user-replaceable intraosseous training pucks. The 6-in-1 comes with:
  • 3 Neck Skins
  • 10 Tracheas
  • 1 Repair Kit
Add To Cart
X
Quantity:
Strategic Operations - Blood Pumping System (BPS)
$0.00
The Blood Pumping System (BPS) is an innovation in patient worn bleeding simulations.Ê It's worn by the patient and mimics a day pack worn by many Soldiers, Sailors, Marines and other personnel around the world.Ê The BPS is self-contained and allows for 4 simultaneous bleeds controlled by a wireless fob with a 50-foot standoff and 3 liters of blood.Ê Each line can be controlled by the operator to simulate both venous and arterial bleeds.Ê The BPS comes in a basic and deluxe model.Basic BPS Comes with:
  • Wireless remote fob
  • 2 batteries
  • 1 battery charger
  • Upper extremity bleeding module
  • Lower extremity bleeding module
  • Technical repair kit
Deluxe BPS Comes with:
  • Wireless remote fob
  • 2 batteries
  • 1 battery charger
  • Upper extremity bleeding module
  • Lower extremity bleeding module
  • Blast trousers
  • Technical repair kit
Add To Cart
X
Quantity:
Strategic Operations - Neck Skins (Repairable)
$0.00
Flesh colored silicone that is 100% repairable with no recurring cost. Neck skin can be rotated so a minimum of 8 cuts can be made before repair is required.
Add To Cart
X
Quantity:
3D Systems - sPro 60
$0.00
Accurate, tough production parts 3D Systems sPro SLS systems share a common architecture to produce high-resolution, durable thermoplastic parts available in medium to large build volumes.

FEAUTRES:
  • Tough and Durable Parts: Industrial-grade performance delivers the toughest applications, print after print.
  • Excellent Part Resolution, Surface Finish and Edge Definition: Print small to large parts with fine detail and sharp edges.
  • Flexibility Through Upgrade Options: Upgradeable with the flexibility to increase speed and resolution to match your needs now and in the future.
  • Open Material Architecture: Broad choice of materials through flexible print parameters.
Add To Cart
X
Quantity:
3D Systems - ProX 800
$0.00
Production SLA for the ultimate in speed, accuracy and operating economics. ProX 800 SLA printer build parts with outstanding surface smoothness, feature resolution, edge definition and tolerances. Offering the broadest range of materials among all 3D printers, they are also highly efficient, with minimal waste. Combined with their exceptional productivity and reliability, it's no wonder that 3D Systems' SLA printers are the #1 choice of professional service bureaus.

FEATURES:
  • Truly Production-Ready: More than 20 million products are manufactured every year on 3D Systems SLA printers. Develop and deliver products without the cost and time of CNC machining or injection molding.
  • Think Big, Print Big: Produce large, whole parts and cut assembly time and part weakness at attachment points.
  • Compelling Economics: Benefit from part costs as much as 25x lower than other precision 3D printing technologies.
Add To Cart
X
Quantity: